Can I Install A Tub Myself?
Can I Install A Tub Myself?
Blog Article
Just about everyone has got their private perception in relation to Tools You Need to Install a New Bathtub .
Installing a bath tub isn't specifically brain surgery, however it does require strong plumbing, carpentry, and occasionally, tiling skills. Changing an old tub with a new one is also a reasonably tough job. If the old tub is conveniently easily accessible, the project can relocate immediately; if you need to open a wall surface to eliminate the old tub and also place the brand-new bathtub, the job is a lot harder. In either case, the task is within a house handyman's abilities, although you will require a helper to vacate the old tub and also embeded in the brand-new one. Make sure you have actually qualified on your own for the job and also are comfortable trying it. Rather than working with a professional to take control of a halfway-completed job, it is much better to consider utilizing one prior to you begin. Chances are you might require an expert plumber to make tube links.
This short article will certainly assist you mount a brand-new bathtub in your shower room if you have actually already acquired a new bathtub and also don't require to transform the plan of your previous water pipes.
Your tools as well as product checklist need to consist of the following:
Getting ready for the Installment
Firstly, the sustaining frame provided with the bathroom needs to be fitted (if required) according to the maker's guidelines. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is essential to make certain that if the faucet comes with a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is likewise practical to fit a sustaining plate under the faucets system to avoid stress on the tub.
Fit the versatile tap adapters to the bottom of both faucets making use of 2 nuts and also olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet with the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bathroom. See to it you make use of every one of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bath ought to now be ready to be suited its last setting.
Removing Old Taps
If you require to change old taps with new ones as a part of your setup, then the first thing you need to do is separate the supply of water. After doing so, turn on the faucets to drain pipes any type of water remaining in the system. The procedure of eliminating the existing taps can be fairly troublesome because of the limited access that is often the situation.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the faucets. Have a fabric all set for the staying water that will certainly come from the pipelines. When the supply pipes have actually been removed, use the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this process. As soon as the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned of any kind of old sealing substance.
Prior to proceeding to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new taps to fit.
Mounting the Bathtub
Making use of the two wood boards under its feet, place the tub in the called for setting. The wood boards are useful in equally spreading the weight of the tub over the area of the boards as opposed to focusing all the weight onto 4 small factors.
The following goal is to make sure that the bathtub is leveled all round. This can be accomplished by checking the spirit level and also adjusting the feet on the tub till the spirit level reviews level.
To set up faucets, fit the bottom of the furthest adaptable tap port to the ideal supply pipe by making a compression join; after that do the very same for the other tap.
Activate the water supply as well as examine all joints and also new pipework for leaks and also tighten them if necessary. Fill the tub as well as likewise examine the overflow outlet as well as the typical electrical outlet for leaks.
Lastly, take care of the bathroom paneling as described in the producer's user's manual. Tiling and also securing around the bath tub should wait until the bathtub has been made use of at the very least when as this will certainly resolve it into its last placement.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic port to avoid damages to the thread. One end of the connector fits on the plastic tail of the faucet and also the various other end provides a connection to the existing supply pipes.
If you need to fit a monobloc, then you will certainly call for reducing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, position the faucet in the placing opening in the bath/basin making sure that the washing machines remain in area in between the tap and the sink. Protect the faucet in position with the supplier provided backnut. Once the tap is safely in position, the supply pipes can be linked to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with regular faucet connectors. The former type ought to be linked to the tap ends initially, tightening only by hand. The supply pipes can later be linked to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the location where the bathroom satisfies the ceramic tile, it is needed to seal the joins with a silicone rubber caulking. This is essential as the fitting can move enough to break a stiff seal, triggering the water to permeate the wall between the bath and the tiling, resulting in problems with wetness and also feasible leakages to the ceiling below.
You can select from a range of coloured sealants to blend in your fixtures and also installations. They are offered in tubes as well as cartridges, as well as are capable of securing spaces as much as a width of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of drenched newspaper or soft rope. Remember to always load the bath tub with water before sealing, to permit the activity experienced when the bathtub is in use. The sealer can fracture relatively early if you do not consider this movement before securing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also conveniently readily available on the marketplace. It is recommended to fit the tiles making use of waterproof or waterproof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I found that write up on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround when surfing the search engines. Sharing is caring. You never know, you may just be doing someone a favor. We love reading our article about Installing A Bathtub.
Get Started
Report this page